P-LOC® hub clamp connectors are a compact alternative to high-pressure flanges. Each joint has two forged hubs, a metal seal ring, a pair of clamps, and four sets of bolts and nuts. Petrol Steel designs, manufactures, and exports them in sizes from DN15 to DN2000 for pressures up to 90 MPa and temperatures from -200 to 600°C.
Key takeaways
- A hub clamp connector is lighter and faster to make up than a high-pressure flange, but it usually costs more per joint. Compare installed cost, not purchase price.
- Do not mix parts from different systems unless the manufacturer confirms compatibility in writing.
- Ask for the design basis, material certificates, and sealing-surface inspection records before you accept any offer.
Why Engineers Look for Something Smaller Than a Flange
Every few years, a project lands on our desk with the same problem in a different coat of paint. The piping class calls for a high-pressure joint, the module is crowded, and there is no room for a stud tensioning tool. Add a weight budget on a skid or topside, and a client has been burned by a leaking flange on hydrogen or hot hydrocarbon service, and the discussion turns to hub clamp connectors. We developed the P-LOC design for exactly this situation, and we have made and exported it for more than a decade. Two forged hubs are welded to the pipe ends. A metal seal ring sits between them. A pair of clamps, drawn together by four sets of bolts and nuts, pulls the hubs onto the ring. Compared with a flanged joint carrying a dozen or more studs, the assembly is shorter, lighter, and faster to assemble. This article is not a sales pitch for every line. It explains when a hub clamp connector earns its place on your line list and what to check before you order one.
How the Metal Seal Works
The seal does not come from a gasket being crushed. It comes from a metal ring that is slightly deformed between two machined sealing surfaces on the hubs. As the clamp bolts are tightened, the hubs are pulled together, and the ring is loaded to create the initial contact. Internal pressure then helps keep the contact load up instead of relieving it. Because there is no soft gasket to creep, relax, or burn out, the joint tolerates temperature cycling and thermal transients better than a conventional gasketed flange. That is why connectors of this kind are specified for hydrogen, cryogenic, high-temperature, and other hard-to-seal duties. It is also why the sealing surfaces deserve respect. A scratch across a seat or a dent on a ring edge is the kind of defect that turns a compact joint into a leak path. Machining finish, surface protection in transit, and on-site handling matter more here than they do on a raised-face flange.
P-LOC Connector or Flange? An Honest Comparison
Neither is better in every case. A flange is standardized and universally understood, and nearly every valve and vessel nozzle arrives with one. A hub clamp connector wins where weight, footprint, make-up time, and leak tolerance dominate cost. It usually costs more per joint, so the case rests on installed cost and downtime, not on the purchase price alone. If your line list has only a handful of joints and plenty of room, flanges are probably the sensible choice. If you have hundreds of joints on a congested module, or you expect to break and remake joints during the life of the plant, the connector deserves a proper evaluation.
| Factor | Flanged joint | P-LOC hub clamp connector |
| Weight and envelope | Heavier, larger bolt circle | Lighter, shorter, smaller diameter |
| Fasteners | A dozen or more studs on high-pressure classes | Four sets of bolts and nuts |
| Make-up and break-out | Slower, tightening sequence over many studs | Faster; fewer fasteners |
| Sealing element | Gasket (soft, spiral-wound, or ring-type) | Metal seal ring |
| Dimensional standard | Published flange standards | System geometry: weld ends machined to your pipe standard |
| Unit price | Lower | Higher; compare installed cost |
Where These Connectors Are Being Specified
The applications we see most are those where a leak is expensive or unsafe. Hydrogen and other small-molecule gases top the list because they find every weakness in a gasketed joint, and new hydrogen piping is typically designed to ASME B31.12. Refining and petrochemical units use the connectors on severe cycling services. Offshore topsides, subsea tie-ins, and skids use them to save weight and space. Cryogenic and LNG-related lines use them for their low-temperature behavior. Power and test-rig builders choose them for compact joints that can be opened and closed many times. For EPC contractors, the choice is often made at the bid stage because it changes pipe-rack weight, supports, and installation hours. None of these uses is a guarantee for your project. Each is a reason to ask the question, and the answer comes from your pressure, temperature, medium, and code.
Materials: Specify the Joint as a System
A hub clamp connector has four material decisions: hub, seal ring, clamp, and bolting. We forge hubs in stainless steel, carbon steel, alloy steel, titanium, and nickel-based superalloys, chosen to match the pipe. The seal ring is usually the most critical part because it must be compatible with the medium and with the hub seats. Clamps and bolting carry the preload, so strength and relaxation behavior at temperature count. A mismatch in thermal expansion between the hub and clamp can change the preload as the line heats up. Sour service adds the hardness and heat-treatment limits of ISO 15156 (NACE MR0175). Where the line carries chlorides or mixed acids, a nickel alloy hub may be the right answer, and our Alloy 625 round bar range is one starting point for hub stock. Tell us the medium first, and we will propose a material set instead of asking you to pick four separate codes.
Read This Before You Mix Parts
This is the question that costs buyers the most. Flanges follow published dimensional standards, so a flange from one maker mates with another’s. Hub clamp connectors work differently. Each system has its own hub geometry, seal ring profile, and clamp design, and in practice no single dimensional standard governs them all. Within the P-LOC system, the hubs, rings, and clamps are designed to work together. We do not recommend fitting our parts with components from another system, and we would give the same advice in reverse, unless the manufacturers confirm compatibility in writing. If you are replacing parts on an existing installation, send us the connector designation, a drawing, or the existing hub dimensions, and we will tell you honestly whether we can match them before we quote. If you are designing a new line, fix the system on the drawing at the start. It is far cheaper to settle this at the bid stage than at commissioning.
Codes, Testing, and Documents to Ask For
Start with the design basis. The connector has to be checked against your piping or vessel code, for example, ASME B31.3 for process piping, B31.8 for gas transmission, B31.12 for hydrogen, and ASME Section VIII for vessels. Ask any supplier how the pressure rating was established, by calculation, by type testing, or by both, and ask for the report. For materials, we supply EN 10204 3.1 certificates with heat traceability and PMI on hubs, rings, and clamps. Hubs are normally checked by dimensional inspection of the sealing surfaces and by NDT such as UT, MT, or PT, as the specification requires. A hydrostatic or leak test of an assembled joint can be arranged, and SGS, BV, or TÜV can witness any step. Agree on these hold points and acceptance criteria in the purchase order, not afterward.
Installation Mistakes That Cause Leaks
Most field leaks trace back to handling, not design. The sealing surfaces were not cleaned. Lubricant was missing on the clamp contact faces or the nut faces. The bolts were tightened unevenly, so the hubs closed at a small angle. A used seal ring was refitted where the procedure calls for a new one. Or the hub faces were dinged in a laydown yard. The cure is dull but effective: follow the make-up procedure, clean and inspect before every assembly, tighten in stages and in sequence, and replace seal rings as the procedure requires. We supply make-up notes and protective packing with every order, and we are happy to review your site procedure before the first joint is made. Replacement components are normally available within one to two weeks.
What to Send With Your Inquiry
A quote for hub clamp connectors moves fast when the inquiry is complete. Send the nominal pipe size and wall thickness, design pressure and temperature, and the medium, including any hydrogen or H₂S content, the hub types required (weld-neck, blind, reducing, or others), materials for the hub, ring, clamp, and bolting, the design code, inspection and certification requirements, the quantity, and, if you are replacing parts, the existing designation or drawing. Petrol Steel Co., Ltd (PESCO) supplies steel pipes, fittings, flanges, and valves to EPC contractors, fabricators, and distributors, and our P-LOC hub clamp connectors are made to your specified dimensions and shipped with traceable certificates. MOQ and lead time are confirmed per RFQ [state your figures]. If a flange is the better answer for your line, we will tell you so.
Send pipe size, pressure, temperature, medium & quantity → Request a quote.
P-LOC is a registered trademark of PETROL STEEL CO., LTD.
FAQ
- What is a P-LOC hub clamp connector?
A compact pipe joint made of two forged hubs, a metal seal ring, a pair of clamps, and four sets of bolts and nuts. - What size, pressure, and temperature range do you supply?
DN15–DN2000, up to 90 MPa and -200 to 600°C. The final rating depends on size, material set, and design basis and is confirmed per RFQ. - Can it replace a flange?
Often, on the pipe side. Equipment with flanged nozzles needs an adapter hub. Check your design code and client approval first. - Can I mix P-LOC parts with another maker’s parts?
We do not recommend it. Mix systems only with written confirmation from both manufacturers. - What documents come with the order?
EN 10204 3.1 certificates with heat traceability, PMI, and inspection records, and third-party inspection by SGS, BV, or TÜV on request. - What do you need for a quote?
Pipe size and wall thickness, design pressure and temperature, medium, hub types, materials, code, inspection requirements, and quantity.

