Incoloy 825 seamless tube to ASTM B163 (and its ASME twin, SB-163) is the nickel-iron-chromium-molybdenum-copper tube that exchanger designers choose when stainless steel starts to lose against acid, chloride, or sour condensate. PETROL STEEL CO., LTD supplies UNS N08825 tube in the annealed condition, with outside diameters up to 3 in. (76.2 mm) and wall thickness within the B163 scope, as a plain-end straight tube or as a U-bent tube [confirm range]. Each lot ships with a producer’s certificate and test report, and third-party inspection by SGS, BV, or TÜV can be arranged before dispatch.
A word on what B163 is, because buyers often confuse it with the pipe standards. It is a condenser and heat-exchanger tube specification. It covers tubes ordered by outside diameter and either average wall or minimum wall, up to 3 in. OD with minimum wall of 0.148 in. (3.76 mm) or less, or average wall of 0.165 in. (4.19 mm) or less. Thicker or larger material belongs under the seamless pipe standard, and we keep those items on a separate page. If your drawing shows a bundle of 19.05 mm or 25.4 mm tubes, this is the page; if it shows a process line at 4 in. And above, go to our Incoloy 825 seamless pipe.
The alloy itself explains its use. B163 limits UNS N08825 to nickel 38.0–46.0%, chromium 19.5–23.5%, molybdenum 2.5–3.5%, copper 1.5–3.0%, titanium 0.6–1.2%, and iron 22.0% minimum, with carbon held to 0.05% maximum. Nickel gives resistance to chloride stress corrosion cracking. Molybdenum and copper give resistance to sulfuric and phosphoric acid and to pitting. Titanium stabilizes the carbon so the tube resists intergranular attack after welding in the tube sheet. This balance is why Alloy 825 shows up in acid coolers, pickling plants, seawater-cooled condensers, flue-gas cooling, and sour-water exchangers.
Under B163, the tube is furnished in the annealed condition. The standard asks for tensile strength of at least 85 ksi (586 MPa), yield strength of at least 35 ksi (241 MPa) at 0.2% offset, and elongation of at least 30% in 2 in. or 50 mm. For small converter sizes, OD 1¼ in. and under, Appendix X2 also lists half-hard and full-hard tempers for N08825, but it is non-mandatory, and the maker must be consulted on available sizes. We tell buyers plainly: if a design needs a cold-worked, higher-strength tube, say so in the inquiry so we can check it before quoting, rather than assume it is covered.
Test requirements are where B163 differs from a general pipe specification. Each tube is subjected to either a hydrostatic test or a nondestructive electric test, and the choice is the manufacturer’s unless the purchase order says otherwise. For N08825, the hydrostatic pressure is calculated from P = 2St/D, using an allowable fiber stress of 21,000 psi (144.8 MPa), where t is the minimum wall and D the outside diameter; the standard sets a 1,000 psi (6.9 MPa) ceiling on the test pressure, and by agreement, the tube can be tested at 1½ times the fiber stress. The electric test follows B829. A flare test is taken on one end of 1% of the finished lengths, with at least one tube per lot, expanding the end by 30% with a 60° tool without cracking. If your fabricator expands tubes into tube sheets, ask for the flare test report with the shipment.
Dimensional control matters as much as chemistry for exchanger work. Table 4 sets outside diameter and wall tolerances, includes ovality, and limits wall eccentricity to ±10% of the measured average wall. Cut lengths are never short of the ordered length, with a plus allowance of 1/8 in. (3.2 mm), rising to 1/4 in. (6.4 mm) over 30 ft (9.1 m). Converter sizes have their own tolerance table, and straightness for small round tubes is held to one part in 600. When you send us a drawing, give OD and minimum or average wall in inches or millimeters, not a gauge number, because B163 orders on those terms.
Finish and form are the choices that surprise buyers late in a project. An annealed N08825 tube is normally supplied either annealed and ground on the outside diameter, where the inside may be bright if annealed in a protective atmosphere, or annealed and pickled with dull matte inside and outside surfaces. For U-bend tubes, Supplementary Requirement S1 applies: leg spacing, wall thinning at the apex, leg length, and squareness of ends are all controlled, and when specified, the hydrostatic test is carried out after bending using a fiber stress of 26,600 psi (183.3 MPa) with a 5-second hold. Bend radius limits depend on tube OD and wall as listed in Table 5. Tell us the bend radius and the leg lengths at the inquiry stage so we can confirm that the tube meets the thinning limit.
Certification and traceability are handled the way an inspector expects. Lots for chemistry are one heat; for mechanical and flare testing, a lot is material from one heat, nominal size, and condition. The standard requires a producer’s certification and a report of test results, and each bundle or shipping container is marked with the material name, condition, specification number, size, weights, consignor and consignee, and order number. We add heat-number marking on request, positive material identification, and a packing list tied to bundle numbers. Third-party witnessing needs to be stated on the purchase order, as Section 4 of the standard requires.
We supply fabricators, EPC contractors, and spare-part buyers in the Middle East, Europe, Southeast Asia, Latin America, and Africa who need N08825 tubes for exchangers, coolers, and condensers. Packing for sea freight uses end caps, wood crates, or strapped bundles with moisture-barrier wrap, and nickel alloy is kept apart from carbon steel to prevent iron contamination. To get a fast and accurate quotation, send OD, WT, grade & quantity, with length, finish, bend radius if U-bent, test requirements, and the edition of the standard. Our engineers will answer with a compliance statement, MOQ, and lead time [confirm].
7. Specification Table (place directly under the opening paragraph)
| Item | Detail |
|---|---|
| Standard | ASTM B163-26 / ASME SB-163 (state edition on PO) |
| Alloy | Incoloy 825, UNS N08825, W.Nr. 2.4858 |
| Product | Seamless condenser and heat-exchanger tube, straight or U-bent |
| Condition | Annealed (Table 2) |
| Outside diameter | Up to 3 in. (76.2 mm) per scope [confirm mill range] |
| Wall thickness | Minimum wall up to 0.148 in. (3.76 mm) or average wall up to 0.165 in. (4.19 mm) |
| Length | Cut to length, plus 1/8 in. (3.2 mm); plus 1/4 in. (6.4 mm) over 30 ft |
| Ends | Plain ends, cut and deburred |
| Finish | Annealed and ground OD, or annealed and pickled |
| Tests | Hydrostatic or electric test, flare test, tension test |
| Documents | Producer’s certificate and test report; MTC; third-party report on request |
| Inspection | SGS/BV/TUV, PMI, UT, or eddy-current as agreed |
Chemical composition, % (Table 1): Ni 38.0–46.0; Cr 19.5–23.5; Mo 2.5–3.5; Cu 1.5–3.0; Ti 0.6–1.2; Fe 22.0 min; C 0.05 max; Mn 1.0 max; Si 0.5 max; S 0.03 max; Al 0.2 max.
Mechanical properties (Table 3 and Table X2.1):
| Condition | Tensile min, ksi (MPa) | Yield 0.2%, min ksi (MPa) | Elongation min. % | Hardness |
|---|---|---|---|---|
| Annealed (standard) | 85 (586) | 35 (241) | 30 | Not specified |
| Half-hard (converter sizes, non-mandatory) | 105 (724) | 75 (517) | 15 | B90 to C25 |
| Full-hard (converter sizes, non-mandatory) | 125 (862) | 100 (689) | 5 | C25 to C35 |
Hardness values are for information only. Half-hard and full-hard apply to OD 1¼ in. and under, as limited by the manufacturer.
8. Market, Industry, and Opportunity SEO Layout
Regions:
- Middle East: Saudi Arabia, UAE, Kuwait, Qatar—seawater-cooled condensers, desalination, and petrochemical coolers
- Europe: Germany, Italy, the Netherlands, and the UK—chemical and pharma exchanger fabricators
- Southeast Asia: Malaysia, Indonesia, Thailand, Vietnam—refinery and fertilizer retubes
- Latin America: Brazil, Mexico, Chile—acid plants and mining hydrometallurgy
- Africa: Egypt, Nigeria, South Africa—power, fertilizer, and mining
- North America: US Gulf, Canada—replacement tube bundles and distributor stock
- Central Asia and India: gas processing and sulfuric acid plants
Industries: sulfuric and phosphoric acid plants; flue-gas desulphurization coolers; seawater and brackish-water condensers; refinery and sour-water exchangers; fertilizer and chemical processing; power generation auxiliaries; pickling and metal finishing lines; hydrometallurgy for mining.
Business opportunities and promotion focus:
- Retube and spare-bundle programs: small-quantity, cut-length orders for plant maintenance.
- Exchanger fabricators: regular supply of straight and U-bent tube for new bundles.
- EPC tender support: compliance matrix against ASTM B163-26 and ASME SB-163, sample certificates.
- One-stop nickel alloy: tube plus pipe, flanges, and fittings of N08825 with consistent heat traceability.
- Content plan: publish a news page “ASTM B163-26 changes for Incoloy 825 tube buyers” and short LinkedIn posts that link back to this page.
9. Top 8 FAQ (use on page and in schema)
- What is ASTM B163, and how is it different from ASTM B423? B163 covers seamless nickel and nickel alloy condenser and heat-exchanger tubes up to 3 in. OD. B423 covers seamless pipe and tube for general corrosion service. Choose by product form and size.
- What mechanical properties does the annealed UNS N08825 tube have under B163? Tensile strength 85 ksi (586 MPa) minimum, yield strength 35 ksi (241 MPa) minimum, and elongation 30% minimum in 2 in. or 50 mm.
- What is the largest size under ASTM B163? Outside diameter 3 in. (76.2 mm) and under, with a minimum wall of 0.148 in. (3.76 mm) or less, or average wall of 0.165 in. (4.19 mm) or less.
- How is each tube tested? Each tube gets either a hydrostatic test or a nondestructive electric test. A flare test is made on one end of 1% of lengths, with one tube per lot at minimum.
- Can you supply a U-bend tube? Yes, to Supplementary Requirement S1, including leg spacing, apex wall, and hydrostatic test after bending when specified [confirm capacity]. Send the bend radius and leg lengths.
- What surface finish is available? Annealed and ground on the outside diameter, or annealed and pickled with a dull matte surface. State the finish on the purchase order.
- Which documents come with the tube? A producer’s certificate with a test report, plus an MTC, a PMI record, and a packing list tied to bundle numbers. SGS, BV, or TÜV inspection is available if stated on the order.
- What do you need for a quotation? OD, minimum or average wall, length, quantity, finish, straight or U-bent, test requirements, and the edition of the standard.






